Minimum Bend Radius for Drag Chain Cables: Table + How to Calculate
Technical guide · Drag chain cables · Data
The bend radius is the single number that decides drag chain cable life — and the one most often got wrong, usually by confusing radius with diameter or by using the fixed-installation figure inside a moving chain. Here is the factor table, the full size table, and how to check your own chain in two minutes.
Radius, diameter, and the factor
Every flexible cable is rated by a bending factor: the minimum bend radius expressed as a multiple of the cable’s outside diameter (OD). “7.5 × OD” on a 10 mm cable means the centreline of the bend must not be tighter than 75 mm radius. Two confusions cause most failures:
- Radius vs diameter: a chain sold as “R75” has a 75 mm radius — but a buyer who reads it as diameter halves the actual bend the cable sees.
- Fixed vs dynamic: the small factor on a datasheet (often 4 × OD) applies to a cable bent once and fixed. Inside a moving chain the dynamic factor applies — for the same cable it is roughly double.
The factors that apply in a drag chain
| Cable / duty | Fixed | Dynamic (in the chain) |
|---|---|---|
| High-flex PVC drag chain cables (EKM5 / EKM6 class) | 4 × OD | 7.5 × OD |
| High-flex PUR drag chain cables (EKM7 class) | 4–5 × OD | 7.5–10 × OD |
| Standard flexible control cables (not chain-rated) | 5–6 × OD | Not rated — do not use in chains |
Always design to the largest cable in the chain: its OD sets the minimum radius for the whole run, and the chain must satisfy it at the cable’s actual position (cables stacked toward the outer radius see a larger bend; the innermost layer is the critical one).
Minimum bend radius by cable diameter
Values in millimetres, rounded up. Find your cable’s OD in the left column — our cable selector lists the OD of every construction.
| Cable OD | Fixed · 4 × OD | Dynamic · 7.5 × OD | Dynamic · 10 × OD |
|---|---|---|---|
| 5 mm | 20 | 38 | 50 |
| 6 mm | 24 | 45 | 60 |
| 7 mm | 28 | 53 | 70 |
| 8 mm | 32 | 60 | 80 |
| 9 mm | 36 | 68 | 90 |
| 10 mm | 40 | 75 | 100 |
| 11 mm | 44 | 83 | 110 |
| 12 mm | 48 | 90 | 120 |
| 14 mm | 56 | 105 | 140 |
| 16 mm | 64 | 120 | 160 |
| 18 mm | 72 | 135 | 180 |
| 20 mm | 80 | 150 | 200 |
| 25 mm | 100 | 188 | 250 |
| 30 mm | 120 | 225 | 300 |
Worked example
A packaging machine chain carries three cables: a 9.5 mm servo cable, a 12.8 mm power cable and a 6.2 mm encoder cable. The largest OD (12.8 mm) governs: 12.8 × 7.5 = 96 mm minimum radius. A chain with R100 satisfies it; the common R75 does not — on paper the cables “fit” the chain, in service the power cable’s conductors fatigue first, typically within the first year. The fix at design stage costs nothing; after installation it costs a chain size.
Why a small shortfall costs so much life
Bending strain in the outer strands grows in proportion to OD ÷ radius. Dropping from 7.5 × to 6 × OD raises strand strain by about a quarter — but fatigue life does not fall by a quarter, it falls off a cliff: flex life ratings (for example 7 million cycles for our medium-speed EKM61100 class) are measured at the rated radius, and manufacturers do not publish — because they cannot warrant — life below it. Treat the table value as a hard floor, not a guideline.
Two-minute check on an existing machine: read the chain’s R value from its side link or order code, measure the largest cable’s OD with calipers over the jacket, and divide. If R ÷ OD is below 7.5 for a PVC chain cable, the installation — not the cable — is your failure risk. Our installation guide covers the other six rules that matter once the radius is right.
Real constructions from our range
The table below uses real constructions from our EKM61100 (medium-speed) and EKM71100 (high-speed) ranges, with the outside diameters listed in the cable selector:
| Stock code | Model | Construction | OD | Fixed · 4 × OD | Dynamic · 7.5 × OD |
|---|---|---|---|---|---|
| H101550001402 | EKM61100 | 0.14×2 | 3.7 | 15 | 28 |
| H101550040004 | EKM61100 | 4.0×4 | 12.1 | 49 | 91 |
| H101550010024 | EKM61100 | 1.0×24 | 16.9 | 68 | 127 |
| I101020001402 | EKM71100 | 0.14×2C | 3.6 | 15 | 27 |
| I101020010012 | EKM71100 | 1.0×12C | 14.0 | 56 | 105 |
| I101020010038 | EKM71100 | 1.0×38C | 22.0 | 88 | 165 |
Meeting the radius is necessary, not sufficient: lay the cables loose in the chain with about 10% free length and keep them separated — the installation guide covers those rules.
Frequently asked questions
- Is the chain radius measured to the inside or the centreline?
- Chain manufacturers state R to the bend centreline of the chain. Cables sitting in the inner layer see a slightly smaller radius, which is one more reason to keep margin above the calculated minimum.
- My cable’s datasheet says 4 × OD. Can I use a 4 × chain?
- No — 4 × OD is the fixed-installation figure for a bend made once. In continuous motion the dynamic factor (7.5 × OD for high-flex PVC types) is the one that applies.
- Does a bigger radius extend cable life beyond the rating?
- It removes radius as the limiting factor, but life then depends on speed, travel, temperature and installation quality. Extra radius never hurts; it just stops helping once other factors dominate.
- What if the cables in one chain have very different diameters?
- The largest sets the radius. If one thick power cable forces an oversized chain for everything else, splitting into two smaller chains is often cheaper than one large one.
Checking a chain size against a real cable?
Every construction in our selector shows its outside diameter, so you can verify the radius before ordering. Or send us the chain R and the cable list — we will check the match for you.
Open the cable selector Request a quoteFeeding drives through the same chain? Pair it with our high-flex power cable. For robot axes and dress packs with tight bend radii, see our robot cables — and when no standard construction meets your radius, we build custom assemblies from 300 m.