LiYCY vs LiYY: Choosing a Shielded Data Cable
Technical guide · Data and bus cables · Selection
LiYCY and LiYY are the same flexible data cable with one difference: the letter C. That letter is a copper braid shield — and whether you need it depends entirely on where the cable runs and what shares its route. This is the short, practical version of the decision.
Read the code
Li = fine-stranded flexible conductors, Y = PVC core insulation, Y = PVC jacket, C = copper braid shield. LiYY is the unshielded base cable; LiYCY adds the overall braid. Both are stationary-to-moderate-flex data and control cables — machine wiring, measurement and signal runs — not drag chain cables (for moving signal duty, see the TRVVSP class).
Side by side
| Point | LiYY | LiYCY |
|---|---|---|
| Shield | None | Tinned copper braid, overall |
| Noise behaviour | Picks up whatever the route offers | Rejects capacitive interference from neighbouring power runs |
| Diameter / handling | Slimmer, softest bend | Slightly larger and stiffer — plan gland and entry space |
| Price | Baseline | A step up for the braid and its termination work |
| Typical home | Inside one cabinet, short protected runs | Between cabinets, along machines, anywhere near drives |
When LiYY is enough
- Runs inside a single control cabinet or enclosure, over short distances.
- Routes with no power cables, drives or contactors nearby.
- Digital signals with healthy noise margins in a controlled electrical environment.
When the C is not optional
- The route leaves the cabinet or runs alongside power and motor cables — above all VFD-fed ones.
- Analog measurement: 4–20 mA loops, temperature and sensor signals, where coupled noise becomes measurement error.
- Long runs across a machine or between machines, where the cable is an antenna for everything it passes.
Terminating the shield: bring the braid out over the full 360° on a shield clamp or EMC gland at the cabinet entry — not a pigtail. For high-frequency interference, bond at both ends; on legacy low-frequency analog loops, follow the instrument maker’s instruction where it calls for single-end bonding to avoid ground-loop currents.
Variants worth knowing
LiYCY (TP) twists the cores in pairs under the braid — the step up when signals are differential (RS-485-style runs, balanced measurement), because twisting cancels magnetic coupling that a braid alone does not. And a boundary worth stating plainly: LiYCY is not a fieldbus cable. PROFIBUS, PROFINET and other bus systems specify impedance-controlled constructions; use the dedicated bus types (our selector has a bus and network group) rather than a look-alike data cable.
Frequently asked questions
- Can LiYCY be used for an encoder?
- For a fixed, protected run it is often used for signal wiring, but encoder feedback on a moving axis belongs in a drag-chain-rated pair construction (TRVVSP / servo feedback types). Match the cable’s flex class to the duty first, then the shielding.
- Is shielded always better?
- An unterminated shield protects nothing, and the braid adds cost, diameter and a termination step. Inside one cabinet on short runs, LiYY is the correct, economical specification. Outside that comfort zone, LiYCY earns its price.
- What sizes exist?
- Our standard table lists 471 LiYCY constructions — core counts from 2 upward, sizes in the 0.14–1.5 mm² data range — each with its outside diameter in the selector, so cabinet entries and glands can be planned before ordering.
- LiYCY for RS-485?
- Prefer the twisted-pair variant, LiYCY (TP), and respect the network’s length and termination rules. For a specified bus system, use its dedicated bus cable instead.
Not sure whether your route needs the shield?
Describe the run — length, what it carries, what it runs next to — and we will specify LiYY, LiYCY or the pair variant, and quote from the standard table.
LiYCY shielded data cables Request a quote