How Many Bending Cycles Do You Actually Need?
Technical guide · Drag chain cables · Bending life
A bending-life figure only means something against the cycles your chain will actually do. “Up to 7 million cycles” is plenty for a chain that strokes once a minute, and far too little for one that strokes ten times a minute, three shifts a day. So count first and pick second: this guide shows how to count the cycles over the cable’s service life, then matches the count to the three grades in our drag chain range.
1. Count your cycles: one stroke out and back
One bending cycle is one full travel of the chain — out and back. Count the strokes, not the metres: a short, fast stroke wears the cable just as surely as a long one, and the chain’s stroke rate is the number that decides the grade.
Cycles = strokes per minute × 60 × hours per day × working days per year × years in service. One cycle is one full travel of the chain — out and back.
| Example | Strokes / min | Hours / day | Days / year | Years | Total cycles | Grade that covers it |
|---|---|---|---|---|---|---|
| A — Slow handling axis | 1 | 8 | 250 | 5 | 600,000 | Medium (up to 7 million) |
| B — Two-shift machine tool | 1 | 16 | 250 | 5 | 1,200,000 | Medium (up to 7 million) |
| C — Fast pick-and-place | 5 | 16 | 250 | 5 | 6,000,000 | High-speed (over 10 million) |
| D — High-speed packaging line | 10 | 16 | 250 | 5 | 12,000,000 | High-speed (over 10 million); PUR if oil or abrasion |
Examples A–D use 250 working days a year and 5 years in service. Put in your own days and years — the arithmetic stays the same. If your count lands close to a grade’s figure, step up a grade: a cable run near its stated limit has no margin left for a tight bend radius or a hot, oily chain.
2. The three grades in our range
Our drag chain range is graded by speed, and each grade states its own bending life. The table below uses only product-page values and selector counts.
| Duty | Family | Jacket | Bending life* | Selector rows |
|---|---|---|---|---|
| Low speed | EKM51 series (EKM51100 / 51373 / 51573) | PVC | Not stated — ask for the grade | 1,036 |
| Medium speed | EKM6 series, TRVV / TRVVP / TRVVSP | PVC (EKM61100) | Up to 7 million cycles | 6,677 |
| High speed | EKM71 series (EKM71100 / 71373 / 71383 / 71573 / 71583) | Special polymer (EKM71100) | Over 10 million cycles | 1,753 |
| High speed | EKM71900 family (EKM71900 / 71973 / 71983) | PUR, glossy or matt | Over 20 million cycles | 2,960 |
* Bending life is stated under factory test conditions. Compare constructions on their own stated figure, not on a catalogue headline.
The low-speed EKM51 series has no published bending-life figure: it is listed in the selector for slower chains. Send the chain speed and the expected cycle count and we will confirm the grade. The selector also lists medium-speed PUR variants (EKM61900 and EKM62900 families, 5,556 rows) — ask for the grade on enquiry there too. Our high-flex power cable range is built on the same idea — fine-stranded conductors and flexible insulation, made for drag chain systems and frequently moving machine parts.
3. Which grade fits your count
The low-speed EKM51 series is for slower chains — its grade is confirmed on enquiry, so the table below starts from the medium-speed grade, whose figure is stated.
| Your counted total | Pick | Why |
|---|---|---|
| Under 1 million | Medium speed — EKM61100 | The volume range, with margin to spare |
| 1–5 million | Medium speed — EKM61100 | Still inside the 7-million figure |
| 5–7 million | High speed — EKM71100 | Too close to the 7-million figure to leave margin |
| 7–10 million | High speed — EKM71100 | Over 10 million cycles covers it |
| 10–20 million | High speed — EKM71100, or PUR EKM71900 | PUR where oil, abrasion or the longest life rules |
| Over 20 million | Ask us | No standard grade states more — send the count and we confirm the construction |
4. Real selector rows: seven sizes across the grades
Seven real stock sizes from our cable selector — stock code, model, construction, outer diameter and weight:
| Stock code | Model | Construction | Outer dia. | Weight |
|---|---|---|---|---|
| G101010001410 | EKM51100 | 0.14×10C | 6.8 mm | 64 kg/km |
| H101550025004 | EKM61100 | 4 × 2.5 mm² | 9.8 mm | 196 kg/km |
| H101560001410 | EKM61373 | 0.14×10C | 6.5 mm | 76 kg/km |
| H102020001010 | TRVV | 0.10×10C | 7.4 mm | 81 kg/km |
| I101020001410 | EKM71100 | 0.14×10C | 6.9 mm | 81 kg/km |
| I101030001410 | EKM71373 | 0.14×10C | 7.4 mm | 109 kg/km |
| J101010001410 | EKM71900 (glossy) | 0.14×10C | 6.9 mm | 81 kg/km |
Find your exact size in the cable selector, or browse the full drag chain cable range.
5. What shortens life even at the right grade
The stated figure assumes the chain is installed right. Five mistakes eat the margin before the cycles do:
| Mistake | What it causes | Fix |
|---|---|---|
| Bending tighter than 7.5× outer diameter | Cores break long before the stated cycles | Size the chain radius from the bend-radius guide, not from a catalogue photo |
| No slack in the chain | The cable pulled tight at full travel | Leave about 10% slack |
| PVC where oil and abrasion rule | Jacket wear long before the cores tire | Step up to PUR (EKM71900) |
| Counting each direction as a cycle | Doubles the count and pushes you a grade too high | One cycle is one full out-and-back travel |
| Sizing by price, not by count | A cable that passes the bench test and fails in the chain | Match the grade to the counted cycles first |
Frequently asked questions
- How do I count bending cycles?
- Multiply strokes per minute × 60 × hours per day × working days per year × years in service. One cycle is one full travel of the chain — out and back, not one direction.
- How many cycles is “enough”?
- Enough is your counted total plus margin. Pick the grade whose stated figure sits above your count — up to 7 million (medium speed), over 10 million (high-speed special polymer) or over 20 million (PUR). If the count lands near a grade’s figure, step up a grade.
- What if my chain needs more than 20 million cycles?
- No standard grade states more than 20 million cycles. Send the stroke rate, the hours and the years and we will confirm the construction. Custom builds start at 300 m.
- Does the bend radius change how many cycles I need?
- No — the radius does not change the count, it changes whether the cable survives it. Keep 7.5× the outer diameter while moving and 4× fixed, with about 10% slack in the chain. The full method is in our guide to minimum bend radius for drag chain cables.
- What if my construction is not in the selector?
- Send the chain speed, the cores, the shielding and the length. Custom builds start at 300 m, and we usually quote within one working day.
Send the stroke rate, hours and years
Send the strokes per minute, the hours per day and the years in service — and the cores you need. We will confirm the grade and quote usually within one working day.
Cable Selector WhatsApp Request a Quote