VFD Cables: Why 3+3 Symmetric Shielding Matters (BPYJVP)
Technical guide · VFD and drive cables · EMC
A variable-frequency drive does not output clean sine-wave power. It outputs fast pulse trains, and everything downstream — common-mode currents, bearing wear, interference in neighbouring cables — follows from that. The motor cable is not an accessory to the EMC design; it is part of it. That is what the symmetric 3+3 construction is for.
What “3+3” means
A conventional four-core motor cable carries three phases plus one protective earth conductor tucked wherever it fits. A 3+3 VFD cable (our BPYJVP) splits the earth into three equal conductors placed symmetrically in the gaps between the three phase cores. The geometry is balanced: every phase sees the same capacitance to earth, the return paths share the same impedance, and high-frequency common-mode current gets a controlled, predictable route back to the drive instead of hunting for one through the machine frame and the motor bearings.
| Selection point | Conventional 4-core | Symmetric 3+3 shielded |
|---|---|---|
| Conductor layout | 3 phases + 1 earth, asymmetric | 3 phases + 3 earth conductors, evenly distributed |
| High-frequency return path | Depends on earth position and installation | Balanced earths + shield provide a controlled path |
| EMC behaviour | Extra mitigation often needed | Designed for low emissions when terminated correctly |
| Bearing-current contribution | Uncontrolled return paths raise the risk | Part of the recognised mitigation strategy |
Two shields, two jobs
BPYJVP carries a dual shield: an inner copper tape wrap giving continuous electrostatic coverage, and an outer copper wire braid (80% coverage density in our construction) that carries the high-frequency currents. Around them: XLPE insulation (low capacitance — every metre of cable adds capacitance the drive must charge at each switching edge, so this matters more as runs get longer) and a 0.6/1 kV rating with Class 5 flexible conductors.
Both shields only work if they are terminated over the full 360° at both ends — EMC gland or shield clamp at the drive cabinet and at the motor terminal box, unshielded tails kept as short as possible. A shield twisted into a pigtail is, at switching frequencies, barely a shield at all: it is the single most common VFD installation error, the same one that haunts servo cabling.
Installation rules for VFD runs
- Keep the shield continuous — avoid joints; where one is unavoidable, maintain full-circumference shield continuity through the enclosure.
- Separate the motor cable from signal and data runs; cross at right angles where crossing is unavoidable.
- Do not use the shield as the protective earth — the 3+3 design has dedicated earth conductors; the shield is an EMC component.
- Follow the drive manufacturer’s EMC instructions for gland plates and bonding — the cable completes that system, it does not replace it.
- On long runs, account for cable capacitance and reflected-wave stress: low-capacitance XLPE construction helps, but permissible length still depends on the drive, switching frequency and motor insulation.
Our range: the cable selector publishes the standard BPYJVP 3+3 constructions with full diameter and weight data. Flexible (BPYJVRP) and other VFD constructions are built to specification — send the drive and motor data and we will match the construction.
Frequently asked questions
- Can I feed a VFD motor with a normal 4-core cable?
- People do, on small drives and short runs — and inherit the risks: radiated emissions, common-mode current through unintended paths, and bearing currents that quietly shorten motor life. Most drive manufacturers’ EMC instructions call for a shielded, symmetric cable; the larger the drive and the longer the run, the less optional it becomes.
- Shield at one end or both ends?
- Both ends, over 360°, for VFD duty. The shield is a high-frequency return path, not a signal screen on an audio cable; single-end termination defeats it at switching frequencies.
- Does a 3+3 cable eliminate bearing currents?
- No cable alone eliminates every bearing-current mechanism — shaft grounding and insulated bearings have their place on large motors. The symmetric shielded cable is the first, standard layer of mitigation and the one the drive makers specify.
- What sizes are standard?
- The selector lists the published BPYJVP constructions by core size with outside diameters. If your drive/motor combination needs a size or a flexible variant outside that table, it is a specification build — ask us with the drive data.
Matching a cable to a drive?
Send the drive model, motor rating and run length. We will confirm the 3+3 construction, the size, and whether the standard table covers it or it is a specification build.
VFD range in the selector Request a quote